This is an old revision of the document!
SSH is enabled by default.
Ethernet required for initial installation.. or, you can use a WiFi dongle.
You must plant a wifi.txt on the eMMC in a specific folder to initiate the WiFi connection process. Would have liked to see a GUI here.
Working on connecting the ODROID N2 to the USB MultiBit DAC in the Schiit Ragnarok.
USB Audio currently only working in EmulationStation & is lost once I enter RetroArch. On true RetroPie, this is fully configurable. In EmuELEC, not so much unfortunately.
I could manually specify the audio device in RetroArch using the list below, or look up best practices for handling USB audio & RetroArch.
EmuELEC:~ # aplay -l **** List of PLAYBACK Hardware Devices **** card 0: AMLAUGESOUND [AML-AUGESOUND], device 0: SPDIF-B-dit-hifi dit-hifi-0 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: AMLAUGESOUND [AML-AUGESOUND], device 1: TDM-C-T9015-audio-hifi T9015-audio-hifi-1 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: AMLAUGESOUND [AML-AUGESOUND], device 2: SPDIF-dit-hifi dit-hifi-2 [] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Multibit [Schiit USB Multibit], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0 EmuELEC:~ #
############################################## # EmuELEC # # Retro emulation for Amlogic Devices # # Based on CoreELEC # ############################################## EmuELEC (official): 2.7.1 (Amlogic-ng.arm) EmuELEC:~ # aplay -L null Discard all samples (playback) or generate zero samples (capture) sysdefault:CARD=AMLAUGESOUND AML-AUGESOUND, Default Audio Device iec958:CARD=AMLAUGESOUND,DEV=0 AML-AUGESOUND, IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=AMLAUGESOUND,DEV=0 AML-AUGESOUND, HDMI Audio Output sysdefault:CARD=Multibit Schiit USB Multibit, USB Audio Default Audio Device front:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio Front speakers surround21:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 2.1 Surround output to Front and Subwoofer speakers surround40:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 4.0 Surround output to Front and Rear speakers surround41:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Multibit,DEV=0 Schiit USB Multibit, USB Audio IEC958 (S/PDIF) Digital Audio Output EmuELEC:~ #
Using that information, we see there are two potential ways to manually specify our audio device in RetroArch.
audio_device = "hw:1:0" audio_device = "sysdefault:CARD=Multibit"
Will test this out.